MUZZLE BRAKES & COMPENSATORS

THE BEST NO PAIN MUZZLES BRAKES ANY WHERE

The NEW Accuracy Systems, Inc. Recoil Reduction Video Clips
Click here for Video Clip #1	Click here for Video Clip #2
This video shows our most efficient muzzle brake on a fully auto rifle. Click here for Video Clip #3	This video shows our most efficient muzzle brake on a bolt action 7mm magnum rifle. Click here for Video Clip #4
Please Note: If movies do not play your browser does not support the Video Tag. You can update your browser or click on the link below the movie to watch it in a different formate.

**WARNING: We will Not Warranty Any Muzzle Brake That We do Not Install!! As well as Conditions Out of Our Control! Always make sure you are competent to Install a Muzzle brake or Compensator, if not find a Gunsmith who is! Make sure the Exit Bullet hole of the Muzzle brake or Compensator is true to the bore and the correct size for the bullet diameter that you will be using! (*Note: Exit hole size should be .020" to .030" in diameter larger than the bullet diameter) Otherwise you will get a bullet strike causing Catastrophic Muzzle Brake or Compensator failure as well as possible injuries to you or someone else!! Again We will not be responsible!!

*NEW Forward or Side Venting ON / Off Muzzle Brake Keeps Noise to a Minimum.

Reduces Felt Recoil From 25% To 50% depending on which mode it is in.

Two pictures above show outer Casing removed (When Outer casing is remove recoil reduction is 50%)

 

Pictures shows fully assembled with Outer Casing

 

20" Long x .750" Diameter barrel shown with Forward Venting casing on.

 

Installed on a ASI H-BAR Mini 14 .750" Diameter barrel. ( Outer Case installed quieting Mode)

 

• When field use of your rifle requires no added muzzle brake noise the outer casing is easily screwed on reducing felt recoil to approximately 20 to 25%.
• When bench shooting and ear plugs can be worn the outer casing easily screws off. Which gives a greater recoil reduction of approximately 40 to 50%.
• No Dust print when shooting in prone position with outer case on or off.
• Size is 1" Diameter x 2.4" Long adding 1.75" to barrel length.
• Weight 3 OZ Approximately.
• Steel construction muzzle brake.
• Comes in 1/2 x 28 TPI for 223 up to .264 calibers or 5/8 x 24 TPI for .264 up to 338 Calibers.
• Offered in Black or Stainless colors.
• Made in the USA
• Comes with crush washer for do it your self installation.
• If your barrel is not threaded we offer a threading and installation service for $149.99. (We only need your barrel action if shipping)

Threads 1/2 x 28 TPI - Order Number - 1/2 x 28 223-264 Black	Threads 1/2 x 28 TPI - Order Number - 1/2 x 28 223-264 Stainless
Threads 5/8 x 24 TPI - Order Number - 5/8 x 24 264-8MM (.323) Black	Threads 5/8 x 24 TPI - Order Number - 5/8 x 24 264-8MM (.323) Stainless
Threads 5/8 x 24 TPI - Order Number - 5/8 x 24 - 338 Black	Threads 5/8 x 24 TPI - Order Number - 5/8 x 24 - 338 Stainless

Pictured above In 416 Satin Stainless Steel

Pictured above In Black Oxide 4140 CM Steel

Pictured above In 416 Brushed Stainless Steel

• A) Is the side view above left.
• B) Is the angled side view with the small 3 top ports visible.
• C) Is Looking down at the top of the muzzle brake with the 3 small top holes fully visible.
• There are no bottom holes which makes the muzzle brake a good choice for prone shooters.
• Length is 2.8", Width is 1.293" at the front and .950" at the rear tapered end.
• This brake not only nullifies the rearward motion, But also keeps the muzzle linear so your target stays in the sight picture in your scope.
• Comes in 5/8 x 24 TPI Threads Only.
• Brake must be indexed for proper alignment of holes.
• Gunsmith installation is recommended but we do offer a back up nut for indexing the brake yourself for $5.99.
• Offered in bullet exit hole size of.250" for 223 calibers & .340" for 30 calibers which can be opened for larger calibers. ** Please specify size when ordering below..
• **We can open up the exit hole here for other size calibers or you can have your gunsmith do this for you will when they install your brake.

3 Port Small Maxi Muzzle Brake - 45% Reduction in felt recoil! **For barrels .750 or less at the muzzle.

A

B

C

Pictured above In 416 Satin Stainless Steel

Pictured above In Black Oxide 4140 CM Steel

Pictured above In 416 Brushed Stainless Steel

• A) Is the side view above left.
• B) Is the angled side view with the small 3 top ports visible.
• C) Is Looking down at the top of the muzzle brake with the 3 small top holes fully visible.
• There are no bottom holes which makes the muzzle brake a good choice for prone shooters.
• Length is 2.065", Width is .925" at the front and .710" at the rear tapered end which can be faced off to fit a .750" Diameter barrel.
• This brake not only nullifies the rearward motion, But also keeps the muzzle linear so your target stays in the sight picture in your scope.
• Comes in 1/2 x 28 TPI & 9/16 x 24 TPI Threads Only.
• Brake must be indexed for proper alignment of holes.
• Gunsmith installation is recommended but we do offer a back up nut for indexing the brake yourself for $5.99.
• Offered in bullet exit hole sizes of.250" for 223 calibers & .340" for 30 calibers. Which can be opened for other calibers by your gunsmith.
• **We can open up the exit hole here for other size calibers for or you can have your gunsmith do this for you will when they install your brake.

Brushed Stainless Finish

Satin Stainless Finish

Black Oxide Finish

• 32 - 360 Degree Counter opposing exhaust ports.
• Brake does not have to be Timed or indexed so it can be screwed right on the existing threads with no additional gunsmithing.
• Length is 2".
• This brake not only nullifies the rearward motion but adds comfort to the shooter.
• If Gunsmith installation is required to thread your barrel we do offer that service. *Please call us for pricing.
• Comes in: 1/2 x 28 TPI, 9/16 x 24 TPI, 5/8 x 24 TPI, 3/4 x 24 TPI.
• Outside diameters: .750", .850, 1" and 1.250". For custom Outside diameter sizes please call in the order and add $40.00.
• Bullet exit hole sizes of .250" for 223 calibers can be opened for larger calibers .340" for 30 caliber's can be opened for larger calibers as well.
• Can be Special ordered by phone, in which we will open to the desired caliber.
• The existing bullet exit ports can be opened by your gunsmith when they are installed.

Brushed Stainless Finish

Satin Stainless Finish

Black Oxide Finish

• 5 Frontal exhaust ports and no side port's providing a 25% reduction in recoil.
• NO added noise like other muzzle brakes.
• Adds approximately 1.5" to length of barrel.
• Outside Diameter is 1.125" *Minimum OD the brake can be turned down to is .900".
• For custom Outside diameter sizes please call in the order and add $40.00.
• Calibers from 17 to 338
• Comes in 5/8 x 24 TPI, 1/2 x 28 TPI, or 9/16 x 24 TPI

6 ported sleek linear compensator redirects sound and concussion away from the shooter and down range.

• Attractive fluting on the brake reduces weight, and creates a lower profile and a clean look.
• A crush washer is included.
• 1/2 x 28 TPI 223/5.56 Calibers or 5/8 x 24 TPI up to .308 Calibers
• Stainless or Black Steel
• Overall Length: 2.26 in
• Outer Diameter: 0.87 in.
• Net Weight: 3.7 oz.
• Material: CM4140 Steel & 303 Stainless

*New Howitzer Style Brake