Threads 1/2 x 28 TPI - Order Number - 1/2 x 28 223-264 Black | Threads 1/2 x 28 TPI - Order Number - 1/2 x 28 223-264 Stainless |
Threads 5/8 x 24 TPI - Order Number - 5/8 x 24 264-8MM (.323) Black | Threads 5/8 x 24 TPI - Order Number - 5/8 x 24 264-8MM (.323) Stainless |
Threads 5/8 x 24 TPI - Order Number - 5/8 x 24 - 338 Black | Threads 5/8 x 24 TPI - Order Number - 5/8 x 24 - 338 Stainless |
A | B | C |
- A) Is the side view above left.
- B) Is the angled side view with the small 3 top ports visible.
- C) Is Looking down at the top of the muzzle brake with the 3 small top holes fully visible.
- There are no bottom holes which makes the muzzle brake a good choice for prone shooters.
- Length is 2.8", Width is 1.293" at the front and .950" at the rear tapered end.
- This brake not only nullifies the rearward motion, But also keeps the muzzle linear so your target stays in the sight picture in your scope.
- Comes in 5/8 x 24 TPI Threads Only.
- Brake must be indexed for proper alignment of holes.
- Gunsmith installation is recommended but we do offer a back up nut for indexing the brake yourself for $5.99.
- Offered in bullet exit hole size of.250" for 223 calibers & .340" for 30 calibers which can be opened for larger calibers. ** Please specify size when ordering below..
- **We can open up the exit hole here for other size calibers or you can have your gunsmith do this for you will when they install your brake.
If you are not sure of the caliber call before ordering.
SATIN STAINLESS Order LMB-SSS |
BLACK OXIDE Order LMB-BO |
BRUSHED STAINLESS Order LMB-BSS |
A | B | C |
- A) Is the side view above left.
- B) Is the angled side view with the small 3 top ports visible.
- C) Is Looking down at the top of the muzzle brake with the 3 small top holes fully visible.
- There are no bottom holes which makes the muzzle brake a good choice for prone shooters.
- Length is 2.065", Width is .925" at the front and .710" at the rear tapered end which can be faced off to fit a .750" Diameter barrel.
- This brake not only nullifies the rearward motion, But also keeps the muzzle linear so your target stays in the sight picture in your scope.
- Comes in 1/2 x 28 TPI & 9/16 x 24 TPI Threads Only.
- Brake must be indexed for proper alignment of holes.
- Gunsmith installation is recommended but we do offer a back up nut for indexing the brake yourself for $5.99.
- Offered in bullet exit hole sizes of.250" for 223 calibers & .340" for 30 calibers. Which can be opened for other calibers by your gunsmith.
- **We can open up the exit hole here for other size calibers for or you can have your gunsmith do this for you will when they install your brake.
If you are not sure of the caliber call before ordering.
SATIN STAINLESS Order SMB-SSS |
BLACK OXIDE Order SMB-BO |
BRUSHED STAINLESS Order SMB-BSS |
Brushed Stainless Finish |
Satin Stainless Finish |
Black Oxide Finish |
- 32 - 360 Degree Counter opposing exhaust ports.
- Brake does not have to be Timed or indexed so it can be screwed right on the existing threads with no additional gunsmithing.
- Length is 2".
- This brake not only nullifies the rearward motion but adds comfort to the shooter.
- If Gunsmith installation is required to thread your barrel we do offer that service. *Please call us for pricing.
- Comes in: 1/2 x 28 TPI, 9/16 x 24 TPI, 5/8 x 24 TPI, 3/4 x 24 TPI.
- Outside diameters: .750", .850, 1" and 1.250". For custom Outside diameter sizes please call in the order and add $40.00.
- Bullet exit hole sizes of .250" for 223 calibers can be opened for larger calibers .340" for 30 caliber's can be opened for larger calibers as well.
- Can be Special ordered by phone, in which we will open to the desired caliber.
- The existing bullet exit ports can be opened by your gunsmith when they are installed.
.750 OD Order 750Maxi360 |
.850 OD Order 850Maxi360 |
1.00 OD Order 1.00Maxi360 |
1.25 OD Order 1.25Maxi360 |
Brushed Stainless Finish |
Satin Stainless Finish |
Black Oxide Finish |
- 5 Frontal exhaust ports and no side port's providing a 25% reduction in recoil.
- NO added noise like other muzzle brakes.
- Adds approximately 1.5" to length of barrel.
- Outside Diameter is 1.125" *Minimum OD the brake can be turned down to is .900".
- For custom Outside diameter sizes please call in the order and add $40.00.
- Calibers from 17 to 338
- Comes in 5/8 x 24 TPI, 1/2 x 28 TPI, or 9/16 x 24 TPI
BRUSHED STAINLESS Order Q BRAKE BS |
SATIN STAINLESS Order Q BRAKE SS |
BLACK OXIDE Order Q BRAKE BO |